Rev 02/28/2011Table of ContentsWarnings and Safe Play Instructions ...pg. 2Protective Surfacing Guidelines ... pg. 3Instructions for
Under deck viewFig. 16.1Roof Board installation refer to Step 16a of your manualHardware2 x 1/4 x 3/4” Pan Bolt (1/4”lockwasher,1/4”atwasher,
2°Flare Out2°Flare OutA: Square and attach (OR13) Roof Support on the outside of (OR14) Side Roof with 1 (H1) 1/4 x 1-1/2” Hex Bolts (with lock washe
Step 22: Assemble Slide SupportsSW2Fig. 22.1S3SW3SW5S31 x SL Support 5/4 x 4 x 42-3/4”1 x SL Upright 5/4 x 4 x 44”1 x SW Block 5/4 x 4 x 3-1/2”
Step 23: Assemble Sprial Wave SlideBottom Section Top Section S6S8Snaps2 x #12 x 3/4” Pan Screw 2 x #12 x 1” Pan ScrewS6HardwareS8Other Parts1 x
1 x 1/4 x 3” Lag Screw (1/4”atwasher)Step 24: Attach Slide Supports to Fort41"SW3SW2LS3LS3A: Dig a at bottom, 8” wide by 6-1/2” deep hole
Step 25: Attach Slide to Fort and Supports41"41"41"S7Fig. 25.1S7SW1SW1x 4SlideSide viewA: Place Slide in the centre between (F13) Pos
Step 26: Attach Spiral Wave BracketsHardware4 x #12 x 1” Pan ScrewS6SW3SW2Spiral wave bracketSW3SW2S6S6Detail ADetail BSpiral wave bracket with pan
Solowave Design™ uses only Premium playground lumber, ensuring the safest product for your children’s use. Although great care has been taken in selec
BIG BACKYARD Consumer Registration CardREVISION: 12/01/09CUT ALONG LINEFirst Name Initial Last NameStreet Apt. No.City State/Province ZIP/Postal
S8(2) Pan Screw #12 x 3/4" (9224603)(2) Spiral Wave Brkt9201500 SW1 - SW5Part Identification (Reduced Part Size)Part Identification (Actual Part
PRODUCT NUMBER: A24573ECARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2)CARTON I.D. STAMP
These steps will apply in combination with the Admiral, Balmoral, and Oriana Roof instructions. Use previous steps as reference only:Step 2Step 6Step
Note: Pre-drill all holes using a 1/8” drill bit before installing the lag screws.Hex Bolt Assembly LockWasherT- NutFlatWasherHe xBoltPredrill Pilot
Fig. 6.1AR11Fig. 6.2Fig. 6.3S4S41 x Floor Joist 5/4 x 4 x 46-1/2”HardwareWood Parts4 x #8x 3” Wood ScrewS4AR11 F17 F172-1/8”5/8”Notice top holes use
1 x 1/4 x 3” Hex Bolt (1/4”lockwasher,1/4”atwasher,1/4”t-nut)OR 1 x 1/4 x 1-1/4” Pan Bolt (1/4”lockwasher,1/4”atwasher,1/4”t-nut
Step 15: Front Wall AssemblyGap 1/4”, Not to Exceed 1/2”Bevelled edge faces outFig. 15.1F5S0x 4 per board52 x #8 x 7/8” Truss Screw 13 x CE Wall Bo
Kommentare zu diesen Handbüchern